After further investigation and setting up syslogging, it apperas that it may actually be that host access that's CAUSING the kernel panic? EDIT: 3/16 - I guess I needed to create a VLAN for my dockers with static IPs, so far that's working, so it's probably not HOST access causing the issue, but rather br0 static IPs being set Apply and start the docker. The docker is assigned an IP from the pool - ; typically the first docker gets the first IP address. The important point is that this docker network will now allow dockers with dedicated local network IP addresses, that can can talk with unRAID Join the conversation. You can post now and register later. If you have an account, sign in now to post with your account. Note: Your post will require moderator approval before it will be visible To configure a container to enable SLAAC, you then need to pass the extra parameters specified. --sysctl [HOST]e_ipv6=0. The container will then have its own IP address based on what the network is advertising (again SLAAC) root@MediaStore:~# docker exec nginx ip addr VM Engine (KVM) [Solved]Bridging network adapter to host. I've looked at the wiki multiple times and in this forum (and Google) though cannot find how I was able to bridge the VM's adapter to the host's. I've already tried the three bridges in settings with no luck as well as assigning a static IP. All I'm after is to get my VM on the
Multiple NIC's, DHCP to Static IP Breaking Docker/VM IP ... - Unraid
Change IP to static. By Bugman June 10, in General Support. Followers 0. Reply to this topic. Start new topic. Bugman Posted June 10, Setting up the Unraid side of the VPN tunnel. If UPnP is enabled on your router and you want to use it in Unraid, go to Settings -> Management Access and confirm "Use UPnP" is set to Yes. On Unraid , go to Settings -> VPN Manager. Give the VPN Tunnel a name, such as "MyHome VPN". Press "Generate Keypair" Eth0 (br0) is the management interface and always has an IP address. Consequently this interface becomes automatically available to docker containers, which can set a different and unqiue IP address (either dynamic or static) for this interface. And unRAID supports both IPv4 and IPv6 addresses for docker containers It is already partially enabled in unRaid by default. This is what Proxmox uses by default for Windows VMs. Go to settings for your Windows VM, and enable XML view in the upper right corner. We will need to edit 2 blocks: add the following to block Easiest solution is to assign a static IP for your Unraid server on your home router. Can typically be found under DHCP settings. That's it. Done. No need to tell the server
Unraid | Setting Up WireGuard® on Unraid
Hello, Im using the unraid Version: I have eth0 for use with the router and I have eth1 for connect to my computer with nic 10gbps, when I make a static ip in eth0 I lose the connection with unraid, "please wait configuring interfaces" and dont stop, for recovery acces I need delete the files rules and network 1) macvlan + host access = bridged containers are able to talk to containers that has static ip's but it crashes the server. 2) ipvlan + host access = bridged containers are able to talk to containers that has static ip's but server loses connection to the outside after a while. 3) ipvlan + no host access = no crashes or connection issues, but General Support. Need help changing the IP address on my Unraid Server. So I built an Unraid server for the purposes of installing Crashplan so that I could give the server to my brother who was passing through. I wanted him to set it up at his house for an off-site Crashplan backup system. I set up Unraid and Crashplan at my house, it all Added the new eth1 with new bridge br1 in settings page and deselected br0 as an option for Docker in Docker Settings panel. Then updated each of my docker containers with the same static ip they had before just on br1. Now Docker bridged traffic with static ip is being processed over a dedicated NIC and this is the longest uptime I've